Use hot knives, which can act like a hot nail.Getting all the gear together to dab can be expensive and time consuming, but there are many ways to enjoy dabs without a dab rig.Īlthough these aren’t the best or most efficient way to consume dabs-you might waste concentrate and not get the full effects or flavor-if you don’t want to invest in a dab rig setup, or simply don’t have one, here’s how you can dab without a rig: Step 4: Turn off the torch and start inhaling while rotating the cap to create convection.Step 3: Light your torch and slowly heat the underside of the nail with the flame several inches away, until the dab begins to bubble and turn into a vapor-typically, this takes less than 10 seconds.Step 2: Cover the nail with a carb cap.Step 1: Load a dab into a clean nail without any residual char from previous dabs.How to cold start dabĬold-start dabbing is easy and typically safer than traditional dabbing. All of these should be removed and disposed of, so your next dab starts on a clean surface, and so you can get the full flavor profile of the new dab. The main downside to cold-start dabs, and low-temp dabs in general, is that they tend to not vaporize all the dab placed in a nail, leaving char, residue, and oil. ![]() By subjecting your nail to less heat, you’ll reduce the potential for breakage and reclaim buildup. The dab will begin to melt at a much lower temperature than traditional dabbing, giving the dabber a more flavorful and terpene-rich hit.Ĭold-start dabbing is also great because you don’t have to wait for the nail to cool as much after each hit.ĭabbing cold will also preserve your hardware better than traditional dabbing. It’s also a form of low-temp dabbing.Īs the name implies, with cold-start dabbing, a dab is placed in a cold nail first, and then heated. Each device is different so be sure to read the instruction manual on how to set it.Ĭold-start dabbing, “reverse dabbing,” or “dabbing cold,” is a different way to dab that preserves terpenes and flavors more than hot dabbing. The easiest way to regulate heat is to use an e-nail or e-rig-these electronic devices allow you to dial in to an exact temperature and don’t require a torch. It’ll tell you the exact temperature so you can add the dab at the right moment. Heat your nail, prepare your dab, and point the gun at the cooling nail. You can also use an infrared dab temperature gun, which uses a sensor or laser to measure heat. Again, you’ll need to experiment to find the sweet spot. Once the nail has cooled so there isn’t a direct pinpoint of heat on your palm, it’s ready for a dab. To do this, try heating the nail with a torch until it’s barely glowing red-about 30 seconds-prepare your dab, and then hold your hand at least 6” away from the cooling nail. This will take a bit of trial and error and is less accurate than using a timer. Some dabbers simply rely on experience and feel the heat radiating off a hot nail with their hand. Dab technology is constantly evolving and new products and accessories are always coming out, but a traditional dab setup requires the following core items. Traditional dabbing with a torch requires several accessories to get a concentrate out of its container and into your lungs. Dab rig setup: Tools you need to dab shatter and wax Vapor travels from the nail into the main chamber of the rig, and is cooled by water before hitting the dabber’s lungs. ![]() A carb cap is placed over the nail and the dabber inhales, controlling the airflow with the carb cap. Cannabis concentrate is placed in the nail and the extreme heat vaporizes it. ![]() To take a dab, the nail of a dab rig is heated with a torch, and allowed to cool to the correct temperature. Nails must be able to withstand high temperatures, in the 400-600☏ range, in order to vaporize dabs. There are many styles of nails and one of the most common is a banger, which looks like a bucket and is usually made of quartz or borosilicate.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |